What is NanoBeam used for?

The NanoBeam directs RF energy in a tighter beamwidth. With the focus in one direction, the NanoBeam blocks or spatially filters out noise, so noise immunity is improved. This feature is especially important in an area crowded with other RF signals of the same or similar frequency.

How do I access ubnt device?

Open your browser (e.g. Internet Explorer, Firefox, Opera, etc.) and type in address bar: http://192.168.1.20 (the default address of the Nano) then press the Enter key. Type in ubnt twice and click OK → (If this window did not appear, there may be a problem with the wiring, the network card or a firewall).

What is the default IP for ubiquiti?

192.168.1.20
The default IP address is 192.168. 1.20. The default username is ubnt, and password is ubnt.

Can NanoBeam connect to NanoStation?

Now you can connect the both NanoStation / NanoBeam / NanoBridge to your network(s) and put the WIFI Bridge into operation. It is recommended to change the access passwords to the configuration panel of the NanoStation / NanoBeam / NanoBridge. Further it is also recommended to bring the firmware up-to-date.

What is Nano beam?

The NanoBeam M is the latest generation of Ubiquiti Networks airMAX CPE for customer locations. It’s extremely versatile and cost-effective to deploy the NanoBeam, which provides increased performance from its faster processor and innovative mechanical design at a low cost.

How do I access UniFi protection remotely?

You can access UniFi Protect anywhere by going to unifi.ui.com and signing in with your Ubiquiti SSO account. If you’d like to connect to Protect directly without going through unifi.ui.com: Make sure your computer and UniFi OS Console are on the same network. Type your UniFi OS Console’s IP address into a web browser.

How do I manage my Ubiquiti devices?

Go to the Devices section and select the device. On its Properties panel, select the Manage tab. Reboot or forget the device: Click Reboot device to reboot the device.

What is the default username and password of Ubnt?

Another scenario involving the default username and password for UniFI Access Points (and many other Ubiquiti products) would be when accessing the unit via SSH – in this case (and if you haven’t already adopted the AP into the controller software as mentioned above), you would then need to use the default username and …

How do I reset my NanoBeam?

Reset Button To reset to factory defaults, press and hold the Reset button for more than 10 seconds while the NanoBeam is powered on. Alternatively, the NanoBeam may be reset remotely via a Reset button located on the bottom of the Gigabit PoE Adapter.

What is Station PtMP?

Point-to-Multipoint links (PtMP): Connects three or more locations, using one Base Station (or Access Point) and multiple CPE devices (Stations) connected to the Access Point.

Where do I find the UBNT on my Nanostation?

Open your browser (e.g. Internet Explorer, Firefox, Opera, etc.) and type in address bar:http://192.168.1.20 (the default address of the Nano) then press the Enter key. Type in ubnt twice and click OK → (If this window did not appear, there may be a problem with the wiring, the network card or a firewall).

How can I connect my nanobeam to the Internet?

Connect the power using one of the following options: • Using the included Gigabit PoE Adapter: Go to Connecting to the PoE Adapter. • Using a separate PoE switch: Connect the Ethernet cable from the NanoBeam’s Ethernetport to a PoE-enabled Ethernet port on the switch.

What makes the Ubiquiti nanobeam AC so good?

The NanoBeam ® AC integrates a separate Wi-Fi radio for fast and easy setup using your mobile device. The NanoBeam ® AC features enhanced protection against ESD events. Ubiquiti’s airMAX ® engine with custom IC dramatically improves TDMA latency and network scalability.

Where do I find UBNT on my computer?

• Open your browser (e.g. Internet Explorer, Firefox, Opera, etc.) and type in address bar: http://192.168.1.20 (the default address of the Nano) then press the Enter key. • Type in ubnt twice and click OK → (If this window did not appear, there may be a problem with the wiring, the network card or a firewall).

What is NanoBeam used for? The NanoBeam directs RF energy in a tighter beamwidth. With the focus in one direction, the NanoBeam blocks or spatially filters out noise, so noise immunity is improved. This feature is especially important in an area crowded with other RF signals of the same or similar frequency. How do I…