Is Dana 44 better than 60?
Is Dana 44 better than 60?
The Dana 44 axles use u-joints that measure 2.18 inches from snap ring to snap ring. The Dana 60 axle uses u-joints that measure three inches from snap ring to snap ring. The Dana 60 has a larger ring gear, larger axle tubes, larger axle shafts, and overall is much stronger.
What jeeps came with Dana 44 axles?
1967–1973 Jeepster Commando and Commando.1974–1991 Wagoneer (Passenger side 1974-1979, Driver side 1983 SJ.2003–2006 TJ Wrangler Rubicon (Front and rear)2007-2018 JK Wrangler Rubicon (Front and rear)2018-2019 JL Wrangler Rubicon (Front and rear)2020 JT Gladiator (Front and rear)
Are Dana 44 axles good?
Both left- and right-side pinion versions are common and lots of parts interchange between different 4x4s that used some version of the Dana 44. It has a good cost-to-strength ratio and can be easily upgraded in many areas because it has plenty of aftermarket support.
Is the Dana 44 strong?
It used to be that the Dana 44 was considered to be a fairly stout axle. But as trails got tougher and tires got larger, the 44 got dumped in favor of even stronger hardware. But the Dana 44 is a pretty stout piece, and many companies offer parts to make your 44 even stronger than it now is.
How can you tell the difference between a Dana 30 and a 44?
The only difference between the JK Dana 30 and Dana 44 is ring gear size, electronic locker, and bigger shafts. You’re better off just starting with an aftermarket Dana 44 that is a “true 44”. With the cost difference between a base Wrangler and a Rubicon, you could get aftermarket Dana 60 axles with lockers.
Can a Dana 30 handle 35s?
Yes, you may twist your axle housing or explode the carrier running 35s, but you could do just the same running 33s. Dana 30 (and 44) JK frontends will also benefit greatly from the installation of HD ball joints, axle shafts, and extra housing reinforcement, such as a truss.
Can you make a Dana 30 strong?
An easy way to add some much needed strength to the Dana 30 front axle is with upgraded axle shafts. Look for ones constructed from stronger chromoly steel for a decent bump in strength.
Can Dana 44 Handle 35’s?
35s and 4.10s drive just fine. You can regear if you want but it isn’t necessary at all. I use mine both on and off-road and never have an issue.
How can I make my Dana 44 stronger?
13:04Suggested clip 37 secondsBulding An Unbreakable Dana 44 – YouTubeYouTubeStart of suggested clipEnd of suggested clip
How much horsepower can a Dana 44 handle?
Can you run 40s on a Dana 44?
Registered. In other words, no, you can’t run a 40″ tire on a dana 44.
How much does it cost to lift a Jeep 2 inches?
For example, a lift kit that can lift the car by up to 12 inches will cost more than a 2-inch lift kit. Small truck lift kits that are compatible with Jeep Wranglers cost ranges from $400 – $12,000. If you want a large truck lift, you will have to part with about $11,000 to $40,000.
What size lift do you need for 40 inch tires?
With flat flares, a 1″ body lift, and some fender well trimming, you can run most 40s on wheels with 3.5″ or less backspacing, with 3.25″ front and rear extended bumpstops.
Does lifting a Jeep cause problems?
If you lift your jeep too high and don’t replace your stock control arms, your wheelbase will be shortened and you may get vibrations in the drive line from improper pinion angles. The taller the lift, the bigger the issue you will have using the stock control arms.
What size lift do I need for 33 inch tires?
A 2.5″ suspension lift coupled with a 1.25″ body lift is adequate for 33’s. The body lift will give you the needed clearance so the tires don’t destroy your fenders at full stuff, otherwise you’ll need to add more bump stop extension, which lessons your up travel. Up travel is important for better ride quality.
How much lift do you need for 35 inch tires?
Upgrading to 35-inch tires: If you plan on upgrading to a 35-inch tire, you will need a lift of at least 2.5 inches for proper clearance. At most you’ll need a 3.5 inch lift.
Is Dana 44 better than 60? The Dana 44 axles use u-joints that measure 2.18 inches from snap ring to snap ring. The Dana 60 axle uses u-joints that measure three inches from snap ring to snap ring. The Dana 60 has a larger ring gear, larger axle tubes, larger axle shafts, and overall is…